Rolls-Royce Cullinan Series I to Series II Exterior Conversion

See the body kit parts, how the front end fits together and how it looks after installation.

After installation
Body kit parts
During installation
Design brief

What we wanted to change

Rolls-Royce named its first SUV after the Cullinan diamond in 2018. The Series II arrived in May 2024 with vertical daytime-running lights and a reshaped lower bumper.

Design brief

A kit for the original car

At OWNSILENT we developed the kit in-house using 3D renders and tuned the headlights for the Series I. Off the car, the wrapped lamps show just how far their housings extend behind the lenses.

Kit details

The grille sets the centreline

Seen straight on, the bright cap runs across the tops of the upright vanes. From the diagonal angle you can see how the cap and vanes sit together.

Kit details

Three openings in one bumper

The wide opening belongs in the centre, below the grille. The two deeper openings sit out at the corners, beneath the headlights.

Kit details

The depth of the black vanes

The insert is a frame carrying a row of vanes. In the side view, you can see how far each vane projects from the frame.

Kit details

The trim beneath the grille

The long strips follow the lower edge of the bumper. Turn one over and you can see the attachment edge that disappears against the panel once fitted.

Kit details

The pieces you can hold in one hand

Square covers, rectangular bezels and narrow surrounds sit beside the larger panels. Their outlines are much easier to distinguish here than on a finished bumper.

Kit details

Where the finishes change

Among the small fittings are painted covers and dark trim edges. We use these close-ups to identify the exact piece when a customer asks about one detail.

Fitment

Behind the headlight

With the outer bumper trim off, the lower support is visible between the lamp and upright grille. The side view places it in the front corner of the car.

Fitment

The bracket beside the lamp

In the wider view, follow the edge of the painted panel towards the lamp opening. The close-ups show the metal attachment point and the gap beside it.

Fitment

What the finished lens conceals

The slim line you see when the lamp is lit is only its outer edge. Below it, the open corner exposes the supports and the underside of the housing.

Paint booth

The bumper on its stand

In the booth the panel stands alone, with the intake openings empty. It is the clearest view of the painted surface before the dark inserts go in.

Paint booth

Following the corner into the wing

The surround has two contours. One edge follows the lamp recess. The other curves back towards the front wheel opening.

Paint booth

Body colour around the intake

Under the booth lights, the paint wraps over the curved outer face and into the lip of the opening. That lip will frame the black insert.

Paint booth

Panels and covers dry separately

A large shaped panel stands upright while the smaller pieces sit apart. Laid out together later, the painted sections can be seen alongside the protected bumper.

Assembly

Bringing the two finishes together

Now the body-colour panels and gloss-black trim are together on the floor. The vanes remain distinct against the light paint, even before they are seated in the bumper.

Assembly

Across the lower face

The longer painted sections span the front. At the corners, a much shorter painted edge runs around each dark insert.

After installation

The grille meets the lamp

On the car, the bright cap sits just above the grille vanes. Its outer end meets the inner edge of the narrow headlamp. Step back and the upright grille still dominates the nose.

After installation

The turn at the front wing

Follow the lens from the grille towards the wheel. Its horizontal line turns down at the outer edge, where it meets the painted wing. This is the change you notice first on this Series I.

After installation

A deeper corner intake

The black vanes now sit back inside the bumper. From the corner you can see the recess. From the front the same vanes read as separate dark bars.

After installation

One line across the lower bumper

Below the grille, the fitted trim draws a horizontal line between the dark openings. The face that held three empty openings in the booth is now complete.

After installation

From the wheel arch forward

Viewed from beside the car, the lamp edge, wing seam and intake are in the same frame. The changes concentrate at the nose of the original Series I.

After installation

The front in context

A three-quarter view shows how far the bumper corners wrap towards the wheels. The wider workshop photographs put that new front alongside the original side profile.

After installation

The assembled car in the bay

The loose pieces beside the vehicle give the finished front a sense of scale. From farther back, the grille reads as one bright centre between the two dark intakes.

After installation

The Series I, seen head-on

Here the upright grille, slim lamps and black corner intakes come together on the car. The full project pairs each fitted detail with its loose component.

See all kit parts and fitted details